Dutton-Lainson Company

15 foot heavy duty winch strap with hook, with breaking strength of 6600 lbs, for winches up to 3700 lbs (strap rating must be 150% of winch rating). 2 inch width. Mounting hardware included.

CSA APPROVED 120 Volt Electric Winch has 10 foot, 3-wire grounded power cord. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 3/16 aircraft cable, pulley block, and snap hook. 1800 lb capacity when double-lined. Emergency crank handle also included in case of power loss. Similar to SA7000AC, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

1400 lb winch with 20 ft strap installed, for horizontal pulling applications. High carbon steel gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Zinc TUFFPLATE finish. Handle included.

Brake winch safety and rugged construction at a more economical price. Raise and lower loads with minimal effort, with load locked in place, even when handle is released. 2500 lb capacity, powder coated copper bronze finish. 175 lb minimum load required for winch to operate properly. Handle included.

Model 6346 12 in. Keel Roller - Fits 5/8 Shaft

120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3 wire grounded power cord. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 3/16 aircraft cable, pulley block, and snap hook. 1800 lb capacity when double-lined. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Similar to 25727, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

CSA APPROVED 120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 ft, 3-wire grounded power cord. 1800 lb capacity when double-lined using pulley block and hook (included). Comes loaded with 50 ft of 3/16 inch aircraft cable. Power in, power out, controlled freewheeling clutch, and automatic brake. Emergency crank handle also included in case of power loss. Similar to SA7015AC, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Similar to 25729, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Protect your vehicle bumper, tailgate, license plate, and your shins! Absorbs blow between coupler and towing vehicle when hook-up is misjudged. Slips onto the coupler flange, no tools required. Molded with U.V. inhibitor, resists deterioration and stays flexible in all kinds of weather. Fits most brands of Class 1, 2, 3, and 4 couplers.

1400 lb winch for horizontal pulling applications. High carbon steel gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Powder coated copper bronze finish. Handle included.

Combines the safety of a brake winch with the convenience of being able to freewheel when needed. When freewheel lever is engaged, cable can be pulled off manually to save time. When lever is disengaged, braking mechanism takes effect to lock load in place, even when handle is released. 2500 lb capacity, zinc TUFFPLATE finish. 175 lb minimum load required for winch to operate properly.

Model 6335 2 in. x 9 in. Guide-On Roller - Fits 1/2 in. Shaft

U-bolt style carrier with lock bracket... just add your own padlock for theft protection. Extra length to allow handling of wide tires and to fit wide tongues. For 8", 9", or 12" wheels. Fits 4 or 5-hole rims, zinc TUFFPLATE finish. Nuts also included.

Handy item that provides quick, safe, and reliable wire connection for all 12 volt DC StrongArm electric winch models and model TW9000. Can also be used with 12 volt remote switch kits. Fits 8 gauge wire. Splice mating connectors into wiring harness, so that wiring harness can remain wired to battery when trailer is not present. One connector can be attached to the bottom of the bumper, and the other goes with the winch (and the shorter section of red wire). When ready to use the winch again, just plug the two connectors together. Optional dust cover (24087) sold separately.

12 Volt Electric Winch is powered by your vehicle battery, using wiring harness (included). Power in, power out, controlled free wheeling clutch, and automatic brake. 3000 lb. load capacity. Comes loaded with 25 ft of 7/32 aircraft cable, and snap hook. Emergency crank handle also included in case of power loss. DC Winches are great for mobile applications, or around water. Mount on ATV’s; Race car trailers (also for moving extra tires); Antique car trailers; Boat trailers; Hay bale moving; Livestock feeding equipment; Large livestock trailers; Boat lifts; Articulating conveyors. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

GOLDENROD heavy duty pump oiler, built to last. Precision machined, replaceable parts throughout; screw cap filler opening, interchangeable spouts, zinc die-cast high pressure pump with precision machined piston. Delivers a drop or stream of oil and stays primed for instant use. Powder coated copper bronze finish. Pint size, with 7-1/2 inch straight spout.

Replacement bowl for models 495 and 496 See-Thru fuel filters. Alcohol-resistant polymer material stands up to harsh weather conditions. With easy-to-use sediment drain valve. (Note: For best results, use GOLDENROD filter wrench for removal of See-Thru bowl, to prevent cracking during element changes). Also included in the box is a replacment bowl gasket, 470-7.

Similar to 24870, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Protects both attached and unattached trailers. Design shields padlock from bolt cutters and hacksaws. TUFFPLATE finish.

Model 6334 2 1/2 in. x 12 in. Guide-On Roller - Fits 5/8 in. Shaft

Designed specifically for easy removal of See-Thru filter bowl. Weather-resistant plastic, with hole for hanging on storage tank. Eliminates problem of cracking bowls during element change process.

1200 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 1-1/8 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 75 pound minimum load required for winch to function properly. Zinc TUFFPLATE base and hardware, powder coated black reel. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

Repair kit for D-L Class 1 couplers. Includes the entire ball clamp assembly, for quick changeout. Easy to assemble- can be adjusted by hand without any tools. Fits models 940, 950, 960, and 970. Meets SAE and V-5 standards. For use with D-L couplers only.

Just attach to stationary post with lag screws provided, slip the outer loop over the gate post, and pull the inner loop back to secure the gate. Fast, easy, simple. No wires to break or loosen over time. Great for gates that are used often - in farming, hunting, fishing, etc. Note: This item is IMPORTED.

Model 6337 2 in. End Cap - Fits 1/2 in. Shaft

Rigid (non-swiveling) jack with 1000 lb capacity. Zinc TUFFPLATE finish, ergonomic handle grip. 15 inches of travel. For tongues up to 25 inches from the ground. Fits tongues up to 3 x 5 inches.

Removable foot for 6418 jack only. Includes quick-attach pin for easy removal. 1000 lb. capacity. Zinc TUFFPLATE finish.

For model TW4000 only, fits 12 gauge wire. Splice mating connectors into wiring harness, so that wiring harness can remain wired to battery when trailer is not present. One connector can be attached to the bottom of the bumper, the other goes with the winch (and the shorter section of red wire). When ready to use the winch again, just plug the two connectors together. Optional dust cover (24087) sold separately.

25 foot heavy duty winch strap with hook, with breaking strength of 6600 lbs, for winches up to 3700 lbs (strap rating must be 150% of winch rating). 2 inch width, mounting hardware included.

GOLDENROD heavy duty pump oiler, built to last. Precision machined, replaceable parts throughout; screw cap filler opening, interchangeable spouts, zinc die-cast high pressure pump with precision machined piston. Delivers a drop or stream of oil and stays primed for instant use. Powder coated copper bronze finish. Pint size, with 7-1/2 inch angle spout.

Fits models 495 and 496 See-Thru fuel filters. NOTE: NOT FOR USE WITH BIODIESEL (see 470-9).

1200 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 1-1/8 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 75 pound minimum load required for winch to function properly. Powder coated copper bronze finish. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

Repair kit for D-L Class 2 and 3 couplers. Includes the entire ball clamp assembly, for quick changeout. Easy to assemble- can be adjusted by hand without any tools. Fits models 980, 981, 982, 985, and 990. Meets SAE and V-5 standards. For use with D-L couplers only.

Model 6336 2 1/2 in. End Cap - Fits 5/8 in. Shaft

12 Volt Electric Winch, with factory-installed remote control (handheld pendant switch with 10 foot cord) is powered by your vehicle battery, using wiring harness (included). Power in, power out, controlled free wheeling clutch, and automatic brake. 3000 lb. load capacity. Comes loaded with 25 ft. of 7/32 aircraft cable, and snap hook. Emergency crank handle also included in case of power loss. DC Winches are great for mobile applications, or around water. Mount on ATV’s; Race car trailers (also for moving extra tires); Antique car trailers; Boat trailers; Hay bale moving; Livestock feeding equipment; Large livestock trailers; Boat lifts; Articulating conveyors. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Gasket for BiO-FLO filter 497, works with 100% biodiesel.

Similar to 25010, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Repair kit for the D-L Class 4 995 coupler. Includes the entire ball clamp assembly, for quick changeout. Easy to assemble- can by adjusted by hand without any tools. For use with the D-L 995 coupler only.

1600 lb winch for horizontal pulling applications. High carbon steel gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Zinc TUFFPLATE finish. Handle included.