Dutton-Lainson Company

1200 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 2-1/2 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 75 pound minimum load required for winch to function properly. Zinc TUFFPLATE base and handle, powder coated black reel. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

Model 6348 3 in. x 3 in. Y-Stop - Fits 1/2 in. Shaft

Handy spare tire carrier is designed so that spare tire can also be used as a dolly wheel. Fits 4 or 5-hole rims with 8, 9 or 12 inch tires. Padlock hole in main shaft. Fits 3 or 4-inch square tongues. Powder coated black finish.

Model 6418A A-frame jack, fits standard A-frame couplers. 1000 lb capacity. Removable wheel or foot sold separately. Zinc TUFFPLATE finish.

Removable wheel fits model 6670, 6670B, 6671, and 6671B. Includes quick-attach pin for easy removal. 1250 lb capacity. Zinc TUFFPLATE finish.

SB50 Series connector, fits onto 6385 Quick Connector. When not trailering, cover open end of plug to keep out dust, mud, etc. To install, slide loop around red wires, so that dust cover always stays in place.

For attaching steel cable on all D-L pulling, brake, and electric winches. Includes bolt and nut.

Model SA9005DC Electric Bale Spike Winch, with Remote Control. No Clutch. 3000 lb load capacity. 12 Volt DC electric motor is powered by vehicle battery using wiring harness (included). Comes complete with heavy-duty remote switch (mounts in or under dash in vehicle cab), 80 am circuit breaker, 15 ft positive and 5 ft negative battery wires, two 10-foot switch-to-winch wires, and 25 ft of 7/32 galvanized aircraft cable. Ideal for bale spike use, for powering vehicle-mounted hoists, for a vehicle winch, or for moving farm machinery. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

GOLDENROD heavy duty pump oiler, built to last. Precision machined, replaceable parts throughout; screw cap filler opening, interchangeable spouts, zinc die-cast high pressure pump with precision machined piston. Delivers a drop or stream of oil and stays primed for instant use. Powder coated copper bronze finish. Pint size, with 10 inch flex spout.

Disposable spin-on canister filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi. Compatible with gasoline, diesel, fuel oil, and related additives including methyl, ethyl, and isopropyl alcohol. Also can be used with biodiesel blends up to 20%. Zinc die-cast top cap with 1 inch NPT pipe fittings.

Model 6418A A-frame jack, with removable wheel. Fits standard A-frame couplers. 1000 lb capacity. Zinc TUFFPLATE finish.

1200 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 2-1/2 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 75 pound minimum load required for winch to function properly. Powder coated copper bronze finish. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

Rigid (non-swiveling) jack with 1250 lb capacity. Zinc TUFFPLATE finish, ergonomic handle grip. 15 inches of travel. For tongues up to 25 inches from the ground. 6 inch poly wheel. Fits tongues up to 3 x 5 inches.

Disposable spin-on canister filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi. Compatible with gasoline, diesel, fuel oil, and related additives including methyl, ethyl, and isopropyl alcohol. Also can be used with biodiesel blends up to 20%. Zinc die-cast top cap with 3/4 inch NPT pipe fittings.

1500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 1-1/8 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 150 pound minimum load required for winch to function properly. Zinc TUFFPLATE base and hardware, powder coated black reel. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

1600 lb winch for horizontal pulling applications. High carbon steel gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Powder coated copper bronze finish. Handle included.

Removable steel foot fits model 6670, 6670B, 6671, and 6671B. Includes quick-attach pin for easy removal. For jacks with capacity up to 5000 lbs. Zinc TUFFPLATE finish.

Rigid (non-swiveling) jack with steel foot, 2000 lb capacity. Zinc TUFFPLATE finish, ergonomic handle grip. 15 inches of travel. For tongues up to 25 inches from the ground. Fits tongues up to 3 x 5 inches.

Black vinyl cover keeps your StrongArm electric winch clean, dry, and looking new. Fits all StrongArm and TW-series electric winches. Water resistant black vinyl. Specially treated for cold weather use. Drawstring for quick closure. Cable opening for easy installation.

3/8 inch cable fastener for attaching cable on D-L hand operated winch models DL400-DL900A, with 3/16 inch cable.

120 Volt Electric Winch has 10 foot, 3 wire grounded power cord. 2700 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 25 ft of 7/32 aircraft cable. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, SEE ITEM 24951. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

WATER-BLOCK spin-on canister absorbs water from gasoline and diesel fuel, and filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Restricts fuel flow as water is absorbed, signaling the need for a canister change. Also can be used with biodiesel blends up to 20%. Zinc die-cast top cap with 1 inch NPT pipe fittings. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi.

Similar to 24872, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

1500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 1-1/8 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 150 pound minimum load required for winch to function properly. Powder coated copper bronze finish. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

CSA APPROVED 120 Volt Electric Winch has 10 foot, 3 wire grounded power cord. 2700 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 25 ft of 7/32 aircraft cable. Emergency crank handle also included in case of power loss. Similar to SA9000AC, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

WATER-BLOCK spin-on canister absorbs water from gasoline and diesel fuel, and filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Restricts fuel flow as water is absorbed, signaling the need for a canister change. Also can be used with biodiesel blends up to 20%. Zinc die-cast top cap with 3/4 inch NPT pipe fittings. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi.

Similar to 24965, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Similar to standard model 595, but can be used with 100% biodiesel. BiO-FLO features include a nickel-plated top cap, special buna rubber gasket that resists swelling, and stainless steel internal element components. Disposable spin-on canister filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi. Zinc die-cast top cap with 1 inch NPT pipe fittings.

Similar to standard model 595, but can be used with 100% biodiesel. BiO-FLO features include a nickel-plated top cap, special buna rubber gasket that resists swelling, and stainless steel internal element components. Disposable spin-on canister filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi. Zinc die-cast top cap with 3/4 inch NPT pipe fittings.

Class 3 (5000 lb) A-frame Quick-Lock trailer coupler, powder coated black finish, fits on 2 inch ball. Includes hole for mounting jack through coupler. Exclusive features: -Easy to adjust without tools -Meets all requirements for SAE J684 & VESC V5 -Quick-Lock Ball Clamp assembly provides a precise fit for proper towing -Black Enamel coated finish for additional rust resistance

1500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover for enclosed braking mechanism, 2-1/2 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 150 pound minimum load required for winch to function properly. Powder coated black reel, zinc TUFFPLATE base and hardware. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

Plastic top cap, fits jacks with 2 inch diameter outer tube. (6400 series boat trailer jacks)

6820 Drop-leg jack, side wind, rigid mount. Lengthen and shorten quickly by pulling lynch pin on drop-leg. Total travel of 30 inches, works well for very tall tongues. Zinc TUFFPLATE finish. Fits tongues up to 3 x 5 inches.

Model 6670 A-frame jack, 2000 lb. Can be welded or bolted to standard A-frame couplers. Powder coated black finish. Removable wheel or foot sold separately.

7/16 inch cable fastener fits DL1100A-DL1402A pulling winches, B1200 and DLB800A brake winches. Works with 3/16, 7/32, or 1/4 inch cable.

120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 foot cord) has 10 foot, 3 wire grounded power cord. 2700 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 25 ft of 7/32 aircraft cable. Emergency crank handle also included in case of power loss. For applications, with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

10 micron replacement canister for model 595 fuel filter.

Zinc TUFFPLATE finish. Fits SA models and TW9000 electric winches. Features spring-loaded safety clip. Allows winch to be operated in the event of a power outage, motor failure, etc.

Similar to 25019, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.