Dutton-Lainson Company

9-1/2 inch offset black plated handle, standard replacement for models DLx1900, DLx1900FC, DLx2300, and DLx2300FC. Can also be used on models DL1602A and DL1802A. Premium cushioned handle grip is softer and more comfortable.

2000 lb 2-speed winch for horizontal pulling applications. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Powder coated copper bronze finish, zinc TUFFPLATE hardware. Handle included.

Gear and bearing kit for jacks 1250 lb to 2000 lb capacity with 2-1/4 inch outer tube with date code after 4296 (week 42 of 1996)

120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3 wire grounded power cord. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 7/32 aircraft cable, pulley block, and snap hook. 4000 lb capacity when double-lined. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Ratcheting handle for DL1602A, DL1802A and DLx1900 pulling winches. Can be cranked in full circular revolutions. Can also be ratcheted for better leverage on steep boat ramps or from an awkward stance (such as trying to bring a boat in without getting your feet wet!). See video link on this page for a demonstration of how it works.. Note: Ratcheting action only works in one direction (pulling the line in), so this item needs to be used in applications where there is room to rotate the handle 360 degrees, in order to let the load out.

Similar to 25046, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Replacement seals and cotter pins for 6202, 6203, 6205, 6502, 6503 and 6505 wheel bearing sets (1-1/16 inch spindle, 1.98 inch hub).

Gear and bearing kit for the DLx-SF and DLx-SW tongue jacks.

CSA APPROVED 120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3-wire grounded power cord. 4000 lb capacity when double-lined with pulley block and hook (included). Comes loaded with 50 ft of 7/32 inch aircraft cable. Power in, power out, controlled freewheeling clutch, and automatic brake. Emergency crank handle also included in case of power loss. Similar to SA12015AC but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Replacement seals and cotter pins for 6204, 6206, 6504 and 6506 wheel bearing sets (1-1/4 inch spindle, 2.328 inch hub).

Similar to 24962, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Replacement seals and cotter pins for 6207, 6208, 6507 and 6508 wheel bearing sets (1-3/8 inch spindle, 2.561 inch hub).

Replacement seals and cotter pins for 6200 and 6500 wheel bearing sets (3/4 inch spindle, 1.781 inch hub).

Replacement seals and cotter pins for 6201 and 6501 wheel bearing sets (3/4 inch spindle, 1.938 inch hub).

2500 lb 2-speed winch for horizontal pulling applications. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Zinc TUFFPLATE finish. Handle included.

Bottom support plate for A-frame jacks. Unfinished, ready to be welded to underside of trailer. Provides extra support, so jack will not lean under load.

1500 lb DC winch for boat trailer use - for boats up to 4000 lbs. Loaded with 2 inch x 20 foot web strap and snap hook. Power-in and free-wheel operation, with positive mechanical brake. Clutch control knob engages gears or releases load in a controlled freewheel mode. Note: In the event of a power loss, this model can be manually operated by using a 5/8 inch socket wrench. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

9-1/2 inch Quick-Attach replacement handle (no nut required). For DL1602ADD, DL1800A, DL2000A, DL2500A, DL3200A, DL3500B, and DLB1550A.

2500 lb 2-speed winch for horizontal pulling applications, with 25 ft strap installed. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Zinc TUFFPLATE finish. Handle included.

1500 lb DC winch for boat trailer use, with factory-installed remote control (handheld pendant switch with 10 ft cord) for boats up to 4000 lbs. Loaded with 2 inch x 20 ft web strap and snap hook. Power-in and free-wheel operation, with positive mechanical brake. Clutch control knob engages gears or releases load in a controlled freewheel mode. Note: In the event of a power loss, this model can be manually operated by using a 5/8 inch socket wrench. NOTE: Maximum run time 4 minutes. See owners manual for more details.

2500 lb 2-speed winch for horizontal pulling applications, with hand brake for manually-controlled load release. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, requiring less effort. Zinc TUFFPLATE finish. Handle included.

2500 lb 2-speed special winch used on ice fishing houses. LEFT- hand drive, plated finish, 6 inch handle. Individually boxed.

2500 lb 2-speed winch for horizontal pulling applications. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Powder coated copper bronze finish, zinc TUFFPLATE hardware. Handle included.

3/4 inch Grease Keeper dust caps with grease zirk and pressure relief valve. Protects wheel bearings from water and dirt with a positive hub seal. Supplies a reserve of lubrication and has built-in positive relief. Longer time between periodic repacking of bearings. Protects and extends bearing life. Zirk permits frequent greasing and relief valve eliminates excess pressure on grease seal. No complicated moving parts or gaskets that require costly maintenance and replacements. Easily installed in seconds, no need to remove hubs. A positive hub seal minimizes water entry when wheels are submerged. Zinc plated finish. Includes two protectors, each with a vinyl cover.

Mounting hardware for D-L tongue jacks. Fits square tongues up to 3 x 5 inches.

3000 lb DC winch designed for vehicle/boat trailer use. For boats up to 9000 lbs. Built to same high quality standards as regular SA-series StrongArm winches, but loaded with 2 inch by 20 foot web strap and hook. Power-in, power-out and freewheel operation with dynamic brake and mechanical friction brake. Includes emergency crank handle in case of power loss. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

3000 lb 12V DC winch with factory-installed remote control (handheld pendant switch with ten ft cord) for boat trailer use. For boats up to 9000 lbs. Built to same high quality standards as regular SA-series StrongArm winches, but loaded with 2 inch x 20 foot web strap and hook. Power-in, power-out and freewheel operation, with dynamic brake as well as mechanical friction brake. Includes emergency crank handle in case of power loss. NOTE: Maximum run time 4 minutes. See owners manual for more details.

Mounting hardware for the DLx-SF and DLx-SW tongue jacks. Fits square tongues up to 3 x 5 inches.

1 inch Grease Keeper dust caps with grease zirk and pressure relief valve. Protects wheel bearings from water and dirt with a positive hub seal. Supplies a reserve of lubrication and has built-in positive relief. Longer time between periodic repacking of bearings. Protects and extends bearing life. Zirk permits frequent greasing and relief valve eliminates excess pressure on grease seal. No complicated moving parts or gaskets that require costly maintenance and replacements. Easily installed in seconds, no need to remove hubs. A positive hub seal minimizes water entry when wheels are submerged. Zinc plated finish. Includes two protectors, each with a vinyl cover. Also fits 1-1/16 inch spindles.

This kit allows you to mount your D-L tongue jack to a square tongue up to 3 x 6 inches. Simply attach the kit to the mounting plate on your jack, then use the bolts that were included with the jack to mount it to the tongue. The series of photos above show what is included, and how to install the extender kit.

7 inch replacement handle for DLB350A, DLB800A and DLB1200A brake winches. Ergonomic handle grip.

2500 lb 2-speed winch for horizontal pulling applications, with hand brake for manually-controlled load release. High carbon steel, heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, requiring less effort. Powder coated copper bronze finish, zinc TUFFPLATE hardware. Handle included.

1-1/4 inch Grease Keeper dust caps with grease zirk and pressure relief valve. Protects wheel bearings from water and dirt with a positive hub seal. Supplies a reserve of lubrication and has built-in positive relief. Longer time between periodic repacking of bearings. Protects and extends bearing life. Zirk permits frequent greasing and relief valve eliminates excess pressure on grease seal. No complicated moving parts or gaskets that require costly maintenance and replacements. Easily installed in seconds, no need to remove hubs. A positive hub seal minimizes water entry when wheels are submerged. Zinc plated finish. Includes two protectors, each with a vinyl cover.

Wheel lock fits 800 and 1000 lb. D-L jacks with 6 inch wheel. Grips wheel to eliminate wheel roll. Step on one end to lock, opposite end to release. Kit includes locking lever, cam and mounting bolt.

9-3/8 replacement handle for DLB1500A, DLB2000A and DLB2500A brake winches. Ergonomic handle grip.

3200 lb 2-speed winch for horizontal pulling applications. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Zinc TUFFPLATE finish. Handle included.

For 4-bolt mount jacks with 3/8 inch swivel pin. Appropriate for jacks up to 1500 lb capacity.

12 inch replacement handle for DLB-series brake winches where a longer handle is beneficial for more force. Ergonomic handle grip.