Dutton-Lainson Company

Replacement spout for 120-series GOLDENROD oilers.

HIRED HAND fence stretcher with third hook allows an infinite length of wire to be stretched. When the ratcheting traveler hook is released in order to get another bite, the extra stationary hook holds the wire tight. U.S. Design Pat. D457,413 S U.S. Pat. 6,105,937, CDN. Pat. 2,224,030

1500 lb worm gear winch with split drum, allowing cable to pull from opposite directions. Loop drive can be operated by shepards hook, and if desired, by a variable speed power drill. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings.

1-1/16 inch spindle O.D., 1.98 outer hub I.D. Cone nbr L44649, cup nbr L44610. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

Model 6624 swivel Ag-Industrial jack, side wind, with 15 inch travel. Includes weld-on bracket and snap ring. 2000 lb. capacity. Powder coated black finish.

Remote switch from part #24054 only. For 12-volt DC StrongArm electric winches. Provides 10 foot remote handheld switch unit for wiring directly to winch. Pendant has 3-position In-Off-Out switch. Due to a plug design change in 2014, a separate female plug is included for winches manufactured earlier.

Replacement spout for 120-series GOLDENROD oilers.

Spring Repair Kit for 400 Fence Stretcher. Includes two clamping springs and one ratchet spring.

1500 lb Worm Gear Winch with 5/8 inch hex drive. Comes with mating handle that can be removed easily without tools. Also allows the winch to be operated with a power drill hooked directly to the drive shaft. Cable capacities: 3/16 in (up to 81 ft)... 7/32 in (up to 61 ft)...1/4 in (up to 43 ft). Smaller or larger cable diameters are not recommended.

1-1/4 inch spindle O.D., 2.328 outer hub I.D. Cone nbr LM67048, cup nbr LM67010. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

25 ft remote switch for 12-volt DC StrongArm electric winches. Provides 25 foot remote handheld switch unit for wiring directly to winch. Pendant has 3-position In-Off-Out switch. Due to a plug design change in 2014, a separate female plug is included for winches manufactured earlier.

Replacement spout for 120-series GOLDENROD oilers.

Spring Repair Kit for 405 Fence Stretcher. Includes two clamping springs, one ratchet spring, and one double ratchet spring.

1500 lb Worm Gear Winch with 5/8 inch hex drive, and split drum, allowing cable to pull from opposite directions. Can be operated by cordless drill with 5/8 inch socket, or by socket-head handle (included). Bronze powder-coated finish. Permanently lubricated bearings.

1-1/16 x 3/4 inch spindle O.D., 1.781 outer hub I.D. Cone nbr LM11949/L44649, cup nbr LM11910/L44610. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

DLx-SF swivel tongue jack with 2000 lb capacity. U.S.-made square tubing. Charcoal gray inner and outer square tubes over zinc TUFFPLATE finish. 12 inches of travel. Unique articulating high density plastic foot (with steel brackets). Dual grease fittings keep interior parts fully lubricated. Premium handle cover and grip is softer and fits your hand better. Drainage holes near bottom of inner post. Bushing between tubes prevents scratching and tightens fit. Vinyl sleeve on 1/2 in swivel pin makes swiveling more comfortable, and pin rotates 90 degrees then back into recessed storage position. Jack rotates easily to horizontal towing position and locks in place. Fits tongues up to 3 x 5 in. Pair with a DLxFC pulling winch to make the ultimate trailering statement.

For 12 volt DC StrongArm electric winches. Permits user to operate winch from location up to 10 feet away. Control box mounts on or next to winch and plugs directly into winch switch pocket without rewiring. Durable handheld pendant switch can be unplugged for safe storage.

Spring Repair Kit for 415 Fence Stretcher. Includes three clamping springs and one ratchet spring.

High tensile wire guides (2). Fits models 400, 405, 415.

2000 lb worm gear winch with regular drum, and handle drive. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings. Handle included. Will hold up to 82 ft of 7/32 cable, or 59 ft of 1/4 cable, or 49 ft of 9/32 cable. Cable sizes smaller or larger than these are not recommended.

1-1/4 x 3/4 inch spindle O.D., 1.781 outer hub I.D. Cone nbr LM11949/LM67048, cup nbr LM11910/LM67010. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

Accessory for use with 6349 and 6372 remote switches on StrongArm 115 volt AC electric winches. Allows user to quickly and easily remove remote for storage and added security when needed. Also replaces plug on 12 volt DC winches with remote, and 6371 DC remote switch kit.

Replacement spout for 120-series GOLDENROD oilers.

2000 lb worm gear winch with regular drum, and loop drive. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings.

1-3/8 x 1-1/16 inch spindle O.D., 1.98 outer hub I.D. Cone nbr L44649/L68149, cup nbr L44610/L68111. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

Replacement spout for 120-series GOLDENROD oilers.

2000 lb worm gear winch with split drum, allowing cable to pull from opposite directions. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings. Handle included.

1-3/8 x 1-1/16 inch spindle O.D., 1.98 outer hub I.D. Cone nbr L44649/L68149, cup nbr L44610/L68110. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

For 12 volt DC StrongArm electric winches. Includes heavy-duty 3-position rotary switch, 80 amp circuit breaker, 15 ft positive wire, 5 ft negative wire, and two 10 ft switch-to-winch wires. Switch can be mounted on vehicle dashboard for easy access. Plugs directly into winch switch pocket without rewiring.

Replacement spout for 120-series GOLDENROD oilers.

Bag of 100 Galvanized T-Post Grips. Use with 440 T-Post Gripper installation tool (sold separately). Grips fit all common sizes of steel T-Posts. Faster, easier and more secure than traditional manual clips.

2000 lb worm gear winch with split drum, allowing cable to pull from opposite directions. Loop drive can be operated by shepards hook, and if desired, by a variable speed power drill. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings.

Fits 700-series GOLDENROD oilers

Model 6377 Switch Pocket Replacement Kit for all SA-series DC electric winches. Includes pocket plate top and bottom, housing shunt spring, bottom contact stud, contact stud with groove, 4 lock washers, 2 machine screw nuts, and 2 lock nuts.

Industrial oiler for tough jobs. Zinc die-cast high pressure pump with precision ground piston, powder coated copper bronze finish with zinc plated top cap. 12 oz, with 8 inch straight spout.

2000 lb Worm Gear Winch with 5/8 inch hex drive. Comes with mating handle that can be removed easily without tools. Also allows the winch to be operated with a power drill hooked directly to the drive shaft. Cable capacities: 7/32 in (up to 82 ft)... 1/4 in (up to 59 ft)... 9/32 in (up to 49 ft). Smaller or larger cable diameters are not recommended.

4-foot roller bunks (pair) attach directly to vertically-mounted 2 x 4 bunk boards, or can be mounted with 6356 brackets (sold separately). A quick, easy and inexpensive way to upgrade bunk trailers to rollers. 14 gauge steel, black powder coated finish, rubber rollers. For boats weighing up to 2500 lbs. The advantage of this style of roller bunks is that each set of rollers has some wobble capabilities (up to roughly 10 degrees), providing some self-alignment with the boat hull. The rated capacity is based on having good contact with all of the rollers, and a reasonably even distribution of weight on the rollers. Rollers must be in contact with straight sections of the boat hull. It is critical to avoid a very large load on the first set of rollers during the unloading and loading process. The boat should float at least part way onto the trailer before contacting rollers, so that all of its weight is not concentrated on the first set of rollers. A concentrated load can crush a single set of rollers, with the potential for damage to the boat hull.

3/4 inch spindle O.D., 1.781 outer hub I.D. Cone nbr LM11949, cup nbr LM11910. Includes 2 bearings with races, 1 grease seal and cotter pin. IMPORTED.

Heavy duty Class 1 welded link chains for trailers up to 2000 lbs. Zinc plated finish to resist rust, with heavy steel hook and safety clip that latches to keep chains attached to tow vehicle. Chain size 3/16 inch, mount with 3/8 inch bolts. Meets SAE and V-5 standards. Two 18-inch chains per package. NOTE: Do not mount chains to trailer tongue with the same bolts used to mount coupler. Cross safety chains under coupling, allowing only enough slack for turns.

Top wind handle with bolt and nut. For use with D-L tongue jacks only.