Dutton-Lainson Company

600 lb winch for horizontal pulling applications. High carbon steel gears, permanently lubricated bearings, ergonomic handle grip. Powder coated copper bronze finish. Handle included.

Brake winch safety and rugged construction at a more economical price. Raise and lower loads with minimal effort, with load locked in place, even when handle is released. 800 lb capacity, powder coated copper bronze finish. 50 lb minimum load required for winch to operate properly. Handle included.

6692 Coupler ball, stainless steel, 2 in ball size, 1 in shank diameter, 2 in shank length. Class 3 rating. IMPORTED.

Class 2 (3500 lb) coupler with pin & chain, fits 3 inch tongue. Zinc TUFFPLATE finish.

Combines the safety of a brake winch with the convenience of being able to freewheel when needed. When freewheel lever is engaged, cable can be pulled off manually, to save time. When lever is disengaged, braking mechanism takes effect to lock load in place, even when handle is released. 800 lb capacity, zinc TUFFPLATE finish. 50 lb minimum load required for winch to operate properly. Handle included.

Deluxe 4-foot roller bunks (pair) attach directly to 2 x 4 bunk boards, or can be mounted with 6389 brackets (sold separately). A quick, easy and inexpensive way to upgrade bunk trailers to rollers. 12 gauge steel, galvanized finish, rubber rollers. For boats weighing up to 2500 lbs. The advantage of this style of roller bunks is that each set of rollers is wider (3 rollers instead of 2), providing more contact with the boat. The rollers on this style of bunk do not have wobble capability for self-alignment like model 6354 does. The rated capacity is based on having good contact with all of the rollers, and a reasonably even distribution of weight on the rollers. Rollers must be in contact with straight sections of the boat hull. It is critical to avoid a very large load on the first set of rollers during the unloading and loading process. The boat should float at least part way onto the trailer before contacting rollers, so that all of its weight is not concentrated on the first set of rollers. A concentrated load can crush a single set of rollers, with the potential for damage to the boat hull.

1-1/16 inch spindle O.D., 1.98 outer hub I.D. Cone nbr L44649, cup nbr L44610. Includes 2 bearings with races, 1 grease seal, and cotter pin. IMPORTED.

Heavy duty Class 3 welded link chains for trailers up to 5000 lbs. Zinc plated finish to resist rust, with heavy steel hook and safety clip that latches to keep chains attached to tow vehicle. Chain size 1/4 inch, mount with 7/16 inch hardened (grade 5) bolts. Meets SAE and V-5 standards. Two 36-inch chains per package. NOTE: Do not mount chains to trailer tongue with the same bolts used to mount coupler. Cross safety chains under coupling, allowing only enough slack for turns.

Side handle for jacks with 2 1/4 inch outer tube with date code after 4296 (week 42 of 1996). Includes softer, more comfortable handle grip and roll pin and bushing. For use with D-L tongue jacks only.

Model 6400A Swivel Tongue Jack, made in USA. Zinc TUFFPLATE finish. Jack rotates easily to horizontal towing position, and locks in place. Fits tongues up to 3 x 5 in.

Model 6633 Ag-Industrial jack, top wind, with 15 inch travel. Includes weld-on mounting tube, and detent pin. 2000 lb capacity. Powder coated black finish.

Model 13E anchor, galvanized finish. Recommended for boats 25-28 feet in length.

Class 2 (3500 lb) coupler w/pin & chain, fits 2 inch tongue. Zinc TUFFPLATE finish.

Wiring harness fits 12 volt DC StrongArm models SA5000, SA7000, SA9000 and SA12000. 25 foot power cable, 8 foot ground cable, #8 wire with switch and 70 amp circuit breaker.

20 foot winch strap with hook, with breaking strength of 2600 lbs, for winches up to 1700 lbs (strap rating must be 150% of winch rating). 2 inch width, includes mounting hardware.

CSA APPROVED 120 Volt Electric Winch has 10 foot, 3-wire grounded power cord. 1200 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 20 ft of 3/16 aircraft cable. Emergency crank handle also included in case of power loss. Similar to SA5000AC, but with additional features required in Canada. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

GOLDENROD heavy duty pump oiler, built to last. Precision machined, replaceable parts throughout; screw cap filler opening, interchangeable spouts, zinc die-cast high pressure pump with precision machined piston. Delivers a drop or stream of oil and stays primed for instant use. Powder coated copper bronze finish. Quart size, with 15 inch flex spout.

Pump oiler with wide base for stability. Zinc die-cast high pressure pump with precision ground piston. 10 oz, with flexible spout. Powder coated copper bronze finish.

Industrial oiler for tough jobs. Zinc die-cast high pressure pump with precision ground piston, powder coated copper bronze finish with zinc plated top cap. 16 oz, with 8 inch flexible spout.

Similar to 24975, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Side handle for the DLx-P tongue jack. Features premium handle cover and softer, more comfortable handle grip. Includes roll pin and bushing.

Model 6430 Swivel Tongue Jack, made in USA. Similar to model 6400, but with large 8 inch slotted wheel for added maneuverability. 1/2 inch swivel pin, zinc TUFFPLATE finish. Jack rotates easily to horizontal towing position and locks in place. Fits trailer tongues up to 3 x 5 inches.

Longer hose for pistol-style guns.