Dutton-Lainson Company

Precision machined metal spray tip adjusts from a fine mist when tightened, to a thin stream when opened one or two turns. Save money by buying cleaners, lubricants, solvents or penetrating oils in bulk, then just fill the container and spray! No more expensive aerosols, no having to deal with how to dispose of them, and better for the environment, too. Drawn from steel, powder coated red finish, leakproof joints. 10 oz capacity.

Industrial oiler for tough jobs. Zinc die-cast high pressure pump with precision ground piston, powder coated copper bronze finish with zinc plated top cap. 12 oz, with 8 inch angle spout.

WATER-BLOCK filter removes water from gasoline and diesel fuel. Water-absorbing polymers trap water, restricting fuel flow when it is time to replace the element. Removes microscopic particles (17 microns) of rust, sand, dirt, scale and line. Also compatible with biodiesel blends up to 20%. Zinc die-cast top cap with 1 inch NPT pipe fittings. See-Thru bowl allows for visual monitoring of fuel flow. Maximum recommended flow rate is 25 gpm. Gravity flow rate is approximately 5 gpm with a 24 inch head. Working pressure up to 150 psi.

Similar to 25532, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people or loads over where people could be present. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Brake winch safety and rugged construction at a more economical price. Raise and lower loads with minimal effort, with load locked in place, even when handle is released. 350 lb capacity, powder coated copper bronze finish. 50 lb minimum load required for winch to operate properly. Handle included.

Model 7E anchor, powder coated black finish. Recommended for boats 15-19 feet in length.

6 oz pump oiler with flexible spout. Plastic container, gray color.

WATER-BLOCK filter removes water from gasoline and diesel fuel. Water-absorbing polymers trap water, restricting fuel flow when it is time to replace the element. Also removes microscopic particles (17 microns) of rust, sand, dirt, scale and lint. Also compatible with biodiesel blends up to 20%. Zinc die-cast top cap with 3/4 inch NPT pipe fittings. See-Thru bowl allows for visual monitoring of fuel flow. Maximum recommended flow rate is 25 gpm. Gravity flow rate is approximately 5 gpm with a 24 inch head. Working pressure up to 150 psi.

6 oz plastic oiler with straight spout. Yellow color.

A combination of item 11002 (which will accept strap), and 11001 (which has a hex drive, to be operated with an electric drill). Reel has matching holes drilled in each side plate for mounting strap. Straps sold separately, see Hand Winch Accessories. Recommended strap is model 6249, 20 foot, item 24240. Handle included for when a drill is not available.

Brake winch safety and rugged construction at a more economical price. Raise and lower loads with minimal effort, with load locked in place, even when handle is released. 800 lb capacity, zinc TUFFPLATE finish. 50 lb minimum load required for winch to operate properly. Handle included.

Standard roller bunk bracket, for mounting models 6354/6355. Zinc TUFFPLATE finish. Sold and priced individually. 4 needed to mount a pair of roller bunks. Allows bunks to be adjusted vertically and angled to cradle the boat hull.

1 inch spindle O.D., 1.98 outer hub I.D. Cone nbr L44643, cup nbr L44610. Includes 2 bearings with races, 1 grease seal, and cotter pin. IMPORTED.

Heavy duty Class 2 welded link chains for trailers up to 3500 lbs. Zinc plated finish to resist rust, with heavy steel hook and safety clip that latches to keep chains attached to tow vehicle. Chain size 5/0, mount with 7/16 inch bolts. Meets SAE and V-5 standards. Two 36-inch chains per package. NOTE: Do not mount chains to trailer tongue with the same bolts used to mount coupler. Cross safety chains under coupling, allowing only enough slack for turns.

Popular 1200 lb. pivoting import tongue jack, tested to D-L standards. Zinc plated. 11 inches of travel. 1/2 inch swivel handle, 6 inch wheel. Individually boxed.

Model 6631 swivel Ag-Industrial jack, top wind, with 10 inch travel. Includes weld-on bracket and snap ring. 2000 lb capacity. Powder coated black finish.

Class 1 (2000 lb) coupler with pin & chain, fits 3 inch tongue. Zinc TUFFPLATE finish.

Ground Fault Circuit Interrupter for 120 volt AC electric winch applications near water. 15 foot 14/3 cord, 15 amp, 125 volt. Breaker mounted 7-1/2 inches from plug.

15 foot winch strap with hook, with breaking strength of 2600 lbs, for DL1100A through DL1602A (strap rating must be 150% of winch rating). 2 inch width, includes 3/8 inch bolt and nut. Note: Installing strap on smaller winches DL600A and DL900A requires a 1/4 x 2.75 inch bolt, which is not included.

120 Volt Electric Winch has 10 foot, 3 wire grounded power cord. 1200 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 20 ft of 3/16 aircraft cable. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Model 6399 2 inch coupler ball, similar to model 6397, but with longer shank for thicker bumpers. Shank is 3/4 inch diameter, 2 inches long.

GOLDENROD heavy duty pump oiler, built to last. Precision machined, replaceable parts throughout; screw cap filler opening, interchangeable spouts, zinc die-cast high pressure pump with precision machined piston. Delivers a drop or stream of oil and stays primed for instant use. Powder coated copper bronze finish. Quart size, with 11 inch angle spout.

Spring bottom oiler - just press on the bottom of the container to dispense fluid. 12 oz, with flexible spout.

Pump oiler with wide base for stability. Zinc die-cast high pressure pump with precision ground piston. 10 oz, with straight spout. Powder coated copper bronze finish.