Dutton-Lainson Company

2000 lb worm gear winch with regular drum, and loop drive. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings.

1-3/8 x 1-1/16 inch spindle O.D., 1.98 outer hub I.D. Cone nbr L44649/L68149, cup nbr L44610/L68111. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

Replacement spout for 120-series GOLDENROD oilers.

2000 lb worm gear winch with split drum, allowing cable to pull from opposite directions. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings. Handle included.

1-3/8 x 1-1/16 inch spindle O.D., 1.98 outer hub I.D. Cone nbr L44649/L68149, cup nbr L44610/L68110. Includes 2 bearings with races, 1 grease seal, cotter pin and dust cap. IMPORTED.

For 12 volt DC StrongArm electric winches. Includes heavy-duty 3-position rotary switch, 80 amp circuit breaker, 15 ft positive wire, 5 ft negative wire, and two 10 ft switch-to-winch wires. Switch can be mounted on vehicle dashboard for easy access. Plugs directly into winch switch pocket without rewiring.

Replacement spout for 120-series GOLDENROD oilers.

Bag of 100 Galvanized T-Post Grips. Use with 440 T-Post Gripper installation tool (sold separately). Grips fit all common sizes of steel T-Posts. Faster, easier and more secure than traditional manual clips.

2000 lb worm gear winch with split drum, allowing cable to pull from opposite directions. Loop drive can be operated by shepards hook, and if desired, by a variable speed power drill. Reel automatically stops turning whenever cranking is stopped, locking load in place. Powder coated copper bronze finish, permanently lubricated bearings.

Fits 700-series GOLDENROD oilers

Model 6377 Switch Pocket Replacement Kit for all SA-series DC electric winches. Includes pocket plate top and bottom, housing shunt spring, bottom contact stud, contact stud with groove, 4 lock washers, 2 machine screw nuts, and 2 lock nuts.

Industrial oiler for tough jobs. Zinc die-cast high pressure pump with precision ground piston, powder coated copper bronze finish with zinc plated top cap. 12 oz, with 8 inch straight spout.

2000 lb Worm Gear Winch with 5/8 inch hex drive. Comes with mating handle that can be removed easily without tools. Also allows the winch to be operated with a power drill hooked directly to the drive shaft. Cable capacities: 7/32 in (up to 82 ft)... 1/4 in (up to 59 ft)... 9/32 in (up to 49 ft). Smaller or larger cable diameters are not recommended.

4-foot roller bunks (pair) attach directly to vertically-mounted 2 x 4 bunk boards, or can be mounted with 6356 brackets (sold separately). A quick, easy and inexpensive way to upgrade bunk trailers to rollers. 14 gauge steel, black powder coated finish, rubber rollers. For boats weighing up to 2500 lbs. The advantage of this style of roller bunks is that each set of rollers has some wobble capabilities (up to roughly 10 degrees), providing some self-alignment with the boat hull. The rated capacity is based on having good contact with all of the rollers, and a reasonably even distribution of weight on the rollers. Rollers must be in contact with straight sections of the boat hull. It is critical to avoid a very large load on the first set of rollers during the unloading and loading process. The boat should float at least part way onto the trailer before contacting rollers, so that all of its weight is not concentrated on the first set of rollers. A concentrated load can crush a single set of rollers, with the potential for damage to the boat hull.

3/4 inch spindle O.D., 1.781 outer hub I.D. Cone nbr LM11949, cup nbr LM11910. Includes 2 bearings with races, 1 grease seal and cotter pin. IMPORTED.

Heavy duty Class 1 welded link chains for trailers up to 2000 lbs. Zinc plated finish to resist rust, with heavy steel hook and safety clip that latches to keep chains attached to tow vehicle. Chain size 3/16 inch, mount with 3/8 inch bolts. Meets SAE and V-5 standards. Two 18-inch chains per package. NOTE: Do not mount chains to trailer tongue with the same bolts used to mount coupler. Cross safety chains under coupling, allowing only enough slack for turns.

Top wind handle with bolt and nut. For use with D-L tongue jacks only.

Model 5E anchor, galvanized finish. Recommended for boats under 15 feet in length.

Class 1 (2000 lb) coupler with pin & chain, fits 2 inch tongue. Zinc TUFFPLATE finish.

Dynamic brake remote control for 120 volt AC StrongArm electric winches. Dual switch controls in/out and off/run. Provides dynamic braking function to supplement mechanical brake on winch, bringing load to an immediate halt without coasting. 10 foot cord length.

Designed for PWC trailer applications. 12 ft strap with hook includes 1 inch x 18 inch loop. Steel hook has a tensile strength of 3750 lbs. Packed with 1/4 x 2-1/2 mounting bolt and locknut.

12 Volt Electric Winch is powered by your vehicle battery, using wiring harness (included). Power in, power out, controlled free wheeling clutch, and automatic brake. 1500 lb. load capacity. Comes loaded with 20 ft of 3/16 aircraft cable, and snap hook. Emergency crank handle also included in case of power loss. DC Winches are great for mobile applications, or around water. Mount on ATV’s; Race car trailers (also for moving extra tires); Antique car trailers; Boat trailers; Hay bale moving; Livestock feeding equipment; Large livestock trailers; Boat lifts; Articulating conveyors. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Fits 700-series GOLDENROD oilers

Pistol pump oiler, 6 oz capacity, with leakproof joints. Straight spout. Flared bottom to prevent tipping.