Dutton-Lainson Company

Side handle for the DLx-SW and DLx-SF tongue jacks. Features premium handle cover and softer, more comfortable handle grip. Includes roll pin and bushing.

Brake winch safety and rugged construction at a more economical price. Raise and lower loads with minimal effort, with load locked in place, even when handle is released. 1200 lb capacity, zinc TUFFPLATE finish. 50 lb minimum load required for winch to operate properly. Handle included.

Pair of 5/16 inch vinyl-coated cables with safety hooks at one end. Provides added towing safety, and vinyl coating prevents rusting. Coil tension eliminates dragging and rattles. Cables extend to 40 inches when straightened. For trailers up to 6500 lbs. Meets SAE and V-5 standards. IMPORTED.

INTERCHANGEABLE Coupler ball, includes 1-7/8 in and 2 inch balls. Two internally threaded balls share the same 3/4 inch shank. Change back and forth between sizes quickly and easily. No need to have two separate balls. Polished chrome finish. 3/4 shank size, but includes adaptor to fit 1 inch hole. IMPORTED.

Deluxe 5-foot roller bunks (pair) attach directly to 2 x 4 bunk boards, or can be mounted with 6389 brackets (sold separately). A quick, easy and inexpensive way to upgrade bunk trailers to rollers. 12 gauge steel, galvanized finish, rubber rollers. For boats weighing up to 3000 lbs. The advantage of this style of roller bunks is that each set of rollers is wider (3 rollers instead of 2), providing more contact with the boat. The rollers on this style of bunk do not have wobble capability for self-alignment like model 6355 does. The rated capacity is based on having good contact with all of the rollers, and a reasonably even distribution of weight on the rollers. Rollers must be in contact with straight sections of the boat hull. It is critical to avoid a very large load on the first set of rollers during the unloading and loading process. The boat should float at least part way onto the trailer before contacting rollers, so that all of its weight is not concentrated on the first set of rollers. A concentrated load can crush a single set of rollers, with the potential for damage to the boat hull.

1-1/4 inch spindle O.D., 2.328 outer hub I.D. Cone nbr LM67048, cup nbr LM67010. Includes 2 bearings with races, 1 grease seal, and cotter pin. IMPORTED.

Replacement 6 inch diameter wheel for D-L jacks with capacities of 800 to 1200 lbs. Tough polypropylene resists flat spots and cold weather cracking. Includes axle bolt and nut, and bushing if required.

Model 6709 Swivel tongue jack for applications where a taller jack is advantageous. Similar to model 6400, but with 12 inches of travel, versus the standard 10 inches. For tongues up to 29 inches from the ground. Zinc TUFFPLATE finish. Fits tongues up to 3 x 5 inches.

Model 6634 swivel Ag-Industrial jack, top wind, with 15 inch travel. Includes weld-on bracket and snap ring. 2000 lb capacity. Powder coated black finish.

Class 2 (3500 lb) coupler with pin & chain, fits 2-1/2 in. tongue. Zinc TUFFPLATE finish.

Replaces or repairs switch end of 6362 wiring harness on SA5000, SA7000, SA9000, and SA12000 StrongArm 12 volt electric winches. Includes switch and short lead wires with heavy butt splice connectors to attach to existing positive and negative wire harness leads for easy installation.

15 foot heavy duty winch strap with hook, with breaking strength of 4000 lbs, for winches up to 2600 lbs (strap rating must be 150% of winch rating). 2 inch width, includes mounting hardware.

120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3 wire grounded power cord. 1200 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 20 ft of 3/16 aircraft cable. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Industrial oiler for tough jobs. Zinc die-cast high pressure pump with precision ground piston, powder coated copper bronze finish with zinc plated top cap. 16 oz, with 8 inch angle spout.

Similar to item 14934, but has handle on LEFT side rather than right like on most winches. For situations where having the handle in the regular orientation will not work. Raise and lower loads with minimal effort. 1200 lb capacity, zinc TUFFPLATE finish. 50 lb minimum load required for winch to operate properly. Special order item, please allow extra 2-3 days. Handle included.

Similar to 25538, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Brake winch safety and rugged construction at a more economical price. Raise and lower loads with minimal effort, with load locked in place, even when handle is released. 1200 lb capacity, powder coated copper bronze finish. 50 lb minimum load required for winch to operate properly. Handle included.

Replacement wheels for model 6800 jack. Includes two 6 inch diameter wheels, axle bolt and nut.

CSA APPROVED 120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3-wire grounded power cord. 1200 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 20 ft of 3/16 inch aircraft cable. Emergency crank handle also included in case of power loss. Similar to SA5015AC, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Similar to 25542, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Combines the safety of a brake winch with the convenience of being able to freewheel when needed. When freewheel lever is engaged, cable can be pulled off manually to save time. When lever is disengaged, braking mechanism takes effect to lock load in place, even when handle is released. 1200 lb capacity, zinc TUFFPLATE finish. 50 lb minimum load required for winch to operate properly. Handle included.

1100 lb winch for horizontal pulling applications. High carbon steel gears, permanently lubricated bearings, ergonomic handle grip. Zinc TUFFPLATE finish. Handle included.

Roller bunk bracket, for mounting galvanized models 6387/6388. Zinc TUFFPLATE finish. Sold and priced individually. 4 needed to mount a pair of roller bunks. Allows bunks to be adjusted vertically and angled to cradle the boat hull.

1-1/16 x 3/4 inch spindle O.D., 1.781 outer hub I.D. Cone nbr LM11949/L44649, cup nbr LM11910/L44610. Includes 2 bearings with races, 1 grease seal, and cotter pin. IMPORTED.