Dutton-Lainson Company

Similar to 25040, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: Maximum run time 4 minutes. See owners manual for more details.

9-1/2 inch black plated handle, standard replacement for models DLx1500 and DLx1500FC. Can also replace 6307. Premium cushion handle grip is softer and more comfortable.

2000 lb 2-speed winch for horizontal pulling applications. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Zinc TUFFPLATE finish. Handle included.

Gear and bearing kit for jacks up to 1000 lb. capacity with 2 inch outer tube with date code between 4296 (week 42 of 1996) and 3397 (week 33 of 1997).

Ball adapter plate for instant mounting of StrongArm electric winch models SA5000, SA7000, SA9000, and SA12000 on vehicle ball hitch. Bolt plate to winch, then slip pear-shaped cutout over any standard front or rear-mounted 1-7/8" or 2" hitch ball. Keyhole allows quick installation and removal. Zinc TUFFPLATE finish.

3500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 3-1/8 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 500 pound minimum load required for winch to function properly. Powder coated black reel, zinc TUFFPLATE base and hardware. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

120 Volt Electric Winch has 10 foot, 3 wire grounded power cord. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 7/32 aircraft cable, pulley block, and snap hook. 4000 lb capacity when double-lined. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

9-1/2 inch offset replacement handle for DL1602A, DL1802A and DLC1800. Ergonomic handle grip.

Similar to 24876, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Designed for ceiling mount applications. 4000 lb rated capacity. Loop drive, for use with shepards hook, often powered by electric drill. Split reel allows for pulling of 2 cables in opposite directions. Zinc TUFFPLATE finish.

2000 lb 2-speed winch for horizontal pulling applications. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, for heavier loads. Powder coated copper bronze finish, zinc TUFFPLATE hardware. Handle included.

CSA APPROVED 120 Volt Electric Winch has 10 foot, 3-wire grounded power cord. 4000 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 7/32 aircraft cable, pulley block, and snap hook. 4000 lb capacity when double-lined. Emergency crank handle also included in case of power loss. Similar to SA12000AC, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

9-1/2 inch offset black plated handle, standard replacement for models DLx1900, DLx1900FC, DLx2300, and DLx2300FC. Can also be used on models DL1602A and DL1802A. Premium cushioned handle grip is softer and more comfortable.

2000 lb 2-speed winch for horizontal pulling applications, with hand brake for manually-controlled load release. High carbon steel heat-treated gears, permanently lubricated bearings, reversible ratchet, ergonomic handle grip. Quick-attach handle allows easy change from high speed to low gear, requiring less effort. Zinc TUFFPLATE finish. Handle included.

Moving your kayak to and from the water has never been easier than with the Dutton-Lainson 7100 Kayak Kaddy. This kit includes an axle, two wheels, two washers, two cotter pins, and three adjustable straps, which allow a snug fit to all kayaks. It assembles and disassembles in seconds, and it can be stored in the hull of the kayak when not in use. Attach the kit to one end of your kayak, then pull it from the other end.

Gear and bearing kit for jacks 1250 lb to 2000 lb capacity with 2-1/4 inch outer tube with date code after 4296 (week 42 of 1996)

120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3 wire grounded power cord. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 50 ft of 7/32 aircraft cable, pulley block, and snap hook. 4000 lb capacity when double-lined. Emergency crank handle also included in case of power loss. For applications with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Ratcheting handle for DL1602A, DL1802A and DLx1900 pulling winches. Can be cranked in full circular revolutions. Can also be ratcheted for better leverage on steep boat ramps or from an awkward stance (such as trying to bring a boat in without getting your feet wet!). See video link on this page for a demonstration of how it works.. Note: Ratcheting action only works in one direction (pulling the line in), so this item needs to be used in applications where there is room to rotate the handle 360 degrees, in order to let the load out.

Similar to 25046, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Replacement seals and cotter pins for 6202, 6203, 6205, 6502, 6503 and 6505 wheel bearing sets (1-1/16 inch spindle, 1.98 inch hub).

Gear and bearing kit for the DLx-SF and DLx-SW tongue jacks.

CSA APPROVED 120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 foot, 3-wire grounded power cord. 4000 lb capacity when double-lined with pulley block and hook (included). Comes loaded with 50 ft of 7/32 inch aircraft cable. Power in, power out, controlled freewheeling clutch, and automatic brake. Emergency crank handle also included in case of power loss. Similar to SA12015AC but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Replacement seals and cotter pins for 6204, 6206, 6504 and 6506 wheel bearing sets (1-1/4 inch spindle, 2.328 inch hub).

Similar to 24962, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.