Dutton-Lainson Company

1500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 1-1/8 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 150 pound minimum load required for winch to function properly. Powder coated copper bronze finish. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

CSA APPROVED 120 Volt Electric Winch has 10 foot, 3 wire grounded power cord. 2700 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 25 ft of 7/32 aircraft cable. Emergency crank handle also included in case of power loss. Similar to SA9000AC, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

WATER-BLOCK spin-on canister absorbs water from gasoline and diesel fuel, and filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Restricts fuel flow as water is absorbed, signaling the need for a canister change. Also can be used with biodiesel blends up to 20%. Zinc die-cast top cap with 3/4 inch NPT pipe fittings. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi.

Similar to 24965, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Similar to standard model 595, but can be used with 100% biodiesel. BiO-FLO features include a nickel-plated top cap, special buna rubber gasket that resists swelling, and stainless steel internal element components. Disposable spin-on canister filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi. Zinc die-cast top cap with 1 inch NPT pipe fittings.

Similar to standard model 595, but can be used with 100% biodiesel. BiO-FLO features include a nickel-plated top cap, special buna rubber gasket that resists swelling, and stainless steel internal element components. Disposable spin-on canister filters microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Maximum recommended flow rate is 25 gpm. Working pressure up to 50 psi. Zinc die-cast top cap with 3/4 inch NPT pipe fittings.

Class 3 (5000 lb) A-frame Quick-Lock trailer coupler, powder coated black finish, fits on 2 inch ball. Includes hole for mounting jack through coupler. Exclusive features: -Easy to adjust without tools -Meets all requirements for SAE J684 & VESC V5 -Quick-Lock Ball Clamp assembly provides a precise fit for proper towing -Black Enamel coated finish for additional rust resistance

1500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover for enclosed braking mechanism, 2-1/2 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 150 pound minimum load required for winch to function properly. Powder coated black reel, zinc TUFFPLATE base and hardware. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

Plastic top cap, fits jacks with 2 inch diameter outer tube. (6400 series boat trailer jacks)

6820 Drop-leg jack, side wind, rigid mount. Lengthen and shorten quickly by pulling lynch pin on drop-leg. Total travel of 30 inches, works well for very tall tongues. Zinc TUFFPLATE finish. Fits tongues up to 3 x 5 inches.

Model 6670 A-frame jack, 2000 lb. Can be welded or bolted to standard A-frame couplers. Powder coated black finish. Removable wheel or foot sold separately.

7/16 inch cable fastener fits DL1100A-DL1402A pulling winches, B1200 and DLB800A brake winches. Works with 3/16, 7/32, or 1/4 inch cable.

120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 foot cord) has 10 foot, 3 wire grounded power cord. 2700 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 25 ft of 7/32 aircraft cable. Emergency crank handle also included in case of power loss. For applications, with access to AC power: Boat lifts; Boat davits; Frame-straightening machines (to pull disabled vehicles up onto machine); Light towers; Marine railway systems; Greenhouse ventilation systems; Aircraft hangars (to pull small aircraft in and out); Opening/closing large horizontal sliding doors; Dumb waiters; General material handling applications. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

10 micron replacement canister for model 595 fuel filter.

Zinc TUFFPLATE finish. Fits SA models and TW9000 electric winches. Features spring-loaded safety clip. Allows winch to be operated in the event of a power outage, motor failure, etc.

Similar to 25019, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

1500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 2-1/2 inch reel hub diameter. Load locks in place when handle is released. Great for grain augers, boat lifts, pickup cranes, etc. Lift and lower with ease. 150 pound minimum load required for winch to function properly. Powder coated copper bronze finish. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

CSA APPROVED 120 Volt Electric Winch with factory-installed remote control (handheld pendant switch with 10 ft cord) has 10 ft, 3-wire grounded cord. 2700 lb capacity. Power in, power out, controlled freewheeling clutch, and automatic brake. Comes loaded with 25 ft of 7/32 inch aircraft cable. Emergency crank handle also included in case of power loss. Similar to SA9015, but with additional features REQUIRED IN CANADA. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

10-micron WATER-BLOCK replacement canister for model 596 fuel filter.

Similar to 25021, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people, or loads over where people could be present. NOTE: MAXIMUM RUN TIME 3 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

10 micron BiO-FLO replacement canister for model 597 fuel filter. For filtering biodiesel fuels.

2500 lb brake winch for industrial use. Extra heavy duty construction for long life. Gear cover enclosed braking mechanism, 1-5/16 inch reel hub diameter. Load locks in place when handle is released - lift and lower with ease. Great for grain augers, boat lifts, pickup cranes, etc. 300 pound minimum load required for winch to function properly. Powder coated black reel, zinc TUFFPLATE base and hardware. Handle included. NOTE: For boat lift applications, handle may be replaced by large wheel (supplied by lift manufacturer).

For use on tilt-bed medium and light-duty PWC, snowmobile, and utility trailers. Automatic latch holds tilt bed securely in place. Spring loaded non-pinching latch for automatic latching and easy release. Hardened latch bars for increased strength. Zinc TUFFPLATE finish.