Dutton-Lainson Company

Pistol pump oiler, 6 oz capacity, with leakproof joints. Straight spout. Flared bottom to prevent tipping.

Precision machined metal spray tip adjusts from a fine mist when tightened, to a thin stream when opened one or two turns. Save money by buying cleaners, lubricants, solvents or penetrating oils in bulk, then just fill the container and spray! No more expensive aerosols, no having to deal with how to dispose of them, and better for the environment, too. Drawn from steel, powder coated red finish, leakproof joints. 6 oz capacity.

Industrial oiler for tough jobs. Zinc die-cast high pressure pump with precision ground piston, powder coated copper bronze finish with zinc plated top cap. 12 oz, with 8 inch flexible spout.

For use with common fuels including regular and unleaded gasoline, diesel fuel, fuel oil, and related additives including methyl, ethyl and isopropyl alcohol. Also compatible with biodiesel blends up to 20%. Removes microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Zinc die-cast top cap with 1 inch NPT pipe fittings. See-Thru bowl allows for visual monitoring of fuel flow. Maximum recommended flow rate is 25 gpm. Gravity flow rate is approximately 5 gpm with a 24 inch head. Working pressure up to 150 psi.

Similar to 25500, but NO CLUTCH, so no freewheeling capability. Suitable for short-distance vertical lifting applications not involving people or loads over where people could be present. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Model 5E anchor, powder coated black finish. Recommended for boats under 15 feet in length.

6 oz. oiler, similar to our regular model 600, but with a case hardened trigger to handle thicker liquids. The trigger and container are powder coated copper bronze. Straight spout. Flared bottom to prevent tipping.

For use with common fuels including regular and unleaded gasoline, diesel fuel, fuel oil, and related additives including methyl, ethyl and isopropyl alcohol. Also compatible with biodiesel blends up to 20%. Removes microscopic particles (10 microns) of rust, sand, dirt, scale and lint. Zinc die-cast top cap with 3/4 inch NPT pipe fittings. See-Thru bowl allows for visual monitoring of fuel flow. Maximum recommended flow rate is 25 gpm. Gravity flow rate is approximately 5 gpm with a 24 inch head. Working pressure up to 150 psi.

6 oz oiler with straight spout. Plastic container, gray color.

Similar to 10970, but has the ability to accept a 2 inch wide winch strap. Reel has matching holes drilled in each side plate. Crank the reel so that the hole is outside of the edge of the base, and bolt can be inserted. A wrench or needle-nose pliers are necessary to hold the nut in position on the opposite side during mounting. The bolt goes through a loop in the end of the strap. Powder coated black finish. Handle included. 2000 lb capacity. Straps sold separately, see Hand Winch Accessories. Recommended strap is model 6249, 20 foot, item 24240.

Brake winch safety and rugged construction at a more economical price. Raise and lower loads with minimal effort, with load locked in place, even when handle is released. 350 lb capacity, zinc TUFFPLATE finish. 50 lb minimum load required for winch to operate properly. Handle included.

5-foot roller bunks (pair) attach directly to vertically-mounted 2 x 4 bunk boards, or can be mounted with 6356 brackets (sold separately). A quick, easy and inexpensive way to upgrade bunk trailers to rollers. 14 gauge steel, black powder coated finish, rubber rollers. For boats weighing up to 3000 lbs. The advantage of this style of roller bunks is that each set of rollers has some wobble capabilities (up to roughly 10 degrees), providing some self-alignment with the boat hull. The rated capacity is based on having good contact with all of the rollers, and a reasonably even distribution of weight on the rollers. Rollers must be in contact with straight sections of the boat hull. It is critical to avoid a very large load on the first set of rollers during the unloading and loading process. The boat should float at least part way onto the trailer before contacting rollers, so that all of its weight is not concentrated on the first set of rollers. A concentrated load can crush a single set of rollers, with the potential for damage to the boat hull.

3/4 inch spindle O.D., 1.938 outer hub I.D. Cone nbr 09067, cup nbr 09195. Includes 2 bearings with races, 1 grease seal and cotter pin. IMPORTED.

Heavy duty Class 1 welded link chains for trailers up to 2000 lbs. Zinc plated finish to resist rust, with heavy steel hook and safety clip that latches to keep chains attached to tow vehicle. Chain size 3/16 inch, mount with 3/8 inch bolts. Meets SAE and V-5 standards. Two 24-inch chains per package. NOTE: Do not mount chains to trailer tongue with the same bolts used to mount coupler. Cross safety chains under coupling, allowing only enough slack for turns.

Side handle for jacks with 2 inch outer tube with date code after 4296 (week 42 of 1996). Includes roll pin and bushing. For use with D-L tongue jacks only.

Model 6630 Ag-Industrial jack, top wind, with 10 inch travel. Includes weld-on mounting tube, and detent pin. 2000 lb capacity. Powder coated black finish.

Class 1 (2000 lb) coupler with pin & chain, fits 2-1/2 in. tongue. Zinc TUFFPLATE finish.

For 120 volt AC StrongArm electric winches. Provides 10 foot remote handheld switch unit for wiring directly to winch. Pendant has 3-position In-Off-Out switch.

12 Volt Electric Winch, with factory-installed remote control (handheld pendant switch with 10 foot cord) is powered by your vehicle battery, using wiring harness (included). Power in, power out, controlled free wheeling clutch, and automatic brake. 1500 lb. load capacity. Comes loaded with 20 ft of 3/16 aircraft cable, and snap hook. Emergency crank handle also included in case of power loss. DC Winches are great for mobile applications, or around water. Mount on ATV’s; Race car trailers (also for moving extra tires); Antique car trailers; Boat trailers; Hay bale moving; Livestock feeding equipment; Large livestock trailers; Boat lifts; Articulating conveyors. What makes StrongArm® electric winches different? Design: -is more compact, allowing it to fit into tight spaces. -is safer, as cable is enclosed inside the cover. On open-reel models, fingers can get caught in cable as it’s reeled in, and any frayed strands can cause cuts. -protects cable, so it’s not exposed to the elements, which accelerates wear and rusting. Unique features: -Clutch release. User can pay out load in neutral and still control it with clutch mechanism. -Spur gear system vs. planetary gears. A planetary gear system generates much more heat, and draws more amps from the power source. Because the motor and gears are attached directly to the spool, the heat build-up from running the winch transfers directly to the drum and cable. In contrast, the StrongArm winch’s spur gear system is much more efficient, it gives off less heat and draws fewer amps. NOTE: THIS WINCH IS BUILT FOR HORIZONTAL PULLING. FOR VERTICAL LIFTING APPLICATIONS, WE RECOMMEND ORDERING A WINCH WITH NO CLUTCH INSTALLED. PRICE IS THE SAME. NOTE: MAXIMUM RUN TIME 4 MINUTES. SEE OWNERS MANUAL FOR MORE DETAILS.

Model 6397 Coupler Ball, 2 inch. Externally threaded with 3/4 x 1-1/2 inch shank. Polished chrome. IMPORTED.

Fits 700-series GOLDENROD oilers

GOLDENROD heavy duty pump oiler, built to last. Precision machined, replaceable parts throughout; screw cap filler opening, interchangeable spouts, zinc die-cast high pressure pump with precision machined piston. Delivers a drop or stream of oil and stays primed for instant use. Powder coated copper bronze finish. Quart size, with 11 inch straight spout.

Spring bottom oiler - just press on the bottom of the container to dispense fluid. 6 oz, with flexible spout.

Pistol pump oiler, 6 oz capacity with leakproof joints. 6 inch flexible spout. Flared bottom to prevent tipping.